Modal Close Button

Visit our e-store and shop now

Excia e-store
Shopee Shop Meun Button
Shopee
Lazada Shop Meun Button
Lazada
Motherhood Shop Meun Button
Motherhood
Loading...

Resources

Expert Corner

Visit the ChemRest site:
Anti-slip vulcanised synthetic rubber

Excellent abrasion and cut resistance
Three times the puncture resistance of latex
Good mechanical performance
Excellent resistance to oil, grease and hydrocarbons
Good resistance to acids, certain organic solvents, pesticides, oils and fuels
No latex proteins
Heat resistance (but no flame resistance)

Relatively rigid
Normally low tear resistance
No chemical resistance against ketones and some chlorinated hydrocarbons methylene chloride and trichloroethylene)

Natural rubber mainly from latex and the rubber tree

Very flexible and elastic
Good grip
Excellent resistance to tearing and bending
Good resistance to abrasion
Very robust
Waterproof
Protects against weak acids, caustics, alcohols and detergents
Protection viruses and bacteria

Poor chemical resistance against oils, greases, hydrocarbons and organic solvents
Proteins may cause allergies

Plastic that is a microporous elastomer

Very flexible and elastic
No latex proteins
Clean – does not shed particles like other polymers
Good resistance to abrasion
Good resistance to oil
Does not harden in the cold
Does not soften in the heat
Excellent perspiration thanks to porous ventilation

Low chemical resistance
Poor resistance to hot water

Impermeable plastic

Flexible at even -20°C
Material softened by a plasticizer
Good electrical insulator
High chemical resistance

Low resistance to cuts, puncturing and heat
Disposable PVC gloves might have pinholes
Low resistance to solvents

Polychloroprene synthetic rubber

Flexible and soft like natural rubber
No latex proteins
Good abrasion and cut resistance
Chemical protection against acids, alcohols, fats, ketones, organic and inorganic solvents, oils, greases and petrochemicals
Heat resistant and flame resistant

Poor grip when wet
No chemical resistance against chlorinated hydrocarbon solvents

Synthetic rubber polymer for heavy chemical protection

Very elastic, even at low temperatures
Excellent chemical resistance against ketones (MEK, acetone) and acids
Low gas permeability

Limited grip
Limited dexterity
Poor mechanical resistance
Poor resistance to aliphatic hydrocarbons (hexane, diesel, gasoline), aromatic hydrocarbons (benzene, toluene, xylene) and halogenated solvents (chloroform and chlorobenzene)

Protects where nothing else protects
Chemical protection against PCBs
Excellent chemical protection against chlorinated, aliphatic and aromatic hydrocarbons

Limited grip
Limited dexterity
Not suitable for ketones, esters and nitro compounds

Cotton

Natural cellulose fibre. Flexible, soft and non-irritating, it protects against mechanical aggression (impacts, low vibration, iron filings, splinters, glass fragments), absorbs perspiration and gives you great comfort when wearing dipped protective gloves continuously. Cotton fibres are mixed with polyester fibres in order to associate comfort with a higher mechanical resistance and more elasticity.

Cotton
Nylon

A lightweight elastic polyamide which is largely lint-free and washable, dries quickly and is resistant to abrasion and deformation. Mixed with cotton and acrylic, it makes the glove more flexible and extends its lifetime.

Nylon
Acrylic

A polymer that is resistant to water, common solvents, acids and weak alkalis, and that is resistant to abrasion and to traction. Soft and warm, it insulates you from the cold. Mixed with cotton, it makes the knit more lightweight.

Acrylic
Aramid

It is lightweight, supple, comfortable and washable. It provides effective protection from cuts (above level 5, with stainless steel reinforcing) and from convective heat and offers durability and performance that far exceed that of leather (5 times higher) and cotton (3 times higher).

Aramid
HPPE

High-performance poly ethylene (HPPE) is flexible, light and durable. As resistant to cutting as a para-aramid but with more resistance to abrasion (ten times more resistant to flexion than a wire), it remains resistant to chemicals, in particular solvents.

HPPE
When buying industrial gloves, an understanding of the numeric or alphabetical codes and symbols used for specifying protection levels in the standards is recommended.
European Directive 89/686/EEC

CATEGORY I
Minor risks.
CATEGORY II
Reversible risks (injury), certified compliant by a notified body.
CATEGORY III
Irreversible risks (corrosion), certified compliant and tested by a notified body whose number is specified.

CE Standards

General Requirements for Protective Gloves

  • Technical information*
  • Glove markings
  • Sizes
  • Level of dexterity (1 to 5)
  • Innocuousness of the glove

*Printed on the packaging or on the user instruction of SHOWA gloves. For further details, contact your distributor or visit the website.
Gloves Giving Protection From Chemicals and Microorganisms

The standard defines the capability of gloves to protect the user against penetration, permeation and degradation by chemicals and microorganisms. It classifies three types of gloves by level of protection (A, B, and C).

Penetration Resistance

The gloves must pass the air leak and/or water leak test, and meet the defined AQL inspection level. In an air leak test the interior of glove is pressurized with air and the surface is checked for holes. In a water leak test the glove is filled with water, and checked for the appearance of water droplets on the outside surface after a defined time period.

AQL (accepted quality level) is a measure of quality assurance based on random sampling procedure according to ISO 2859-1 used by manufacturers for measuring the likelihood of pinhole defects in a batch of gloves. An AQL of 1,5 accepts the statistical probability that there are less than 1.5% of the gloves with defects in the batch.

Performance level Acceptable quality level unit Inspection levels
Level 3 under 0,65 G1
Level 2 under 1,5 G1
Level 1 under 4,0 S4
(replaces EN 374-3) Resistance to chemical permeation - Until 21/04/2018

Test method to measure the resistance of the PPE material to permeation by hazardous chemicals at molecular level and under continuous contact. The resulting value is the breakthrough time or the time needed by the hazardous liquid or gas to get in contact with the skin. The glove is classified in terms of breakthrough time performance level 1 to 6.

Measured breakthrough time Permeation performance index
> 10 1
> 30 2
> 60 3
> 120 4
> 240 5
> 480 6

The standard defines a list of 18 chemicals. The minimum breakthrough time for a Type A glove is 30 mins (Level 2) for 6 chemicals, for a Type B it is 30 mins for at least 3 chemicals, and for Type C it is 10 mins (Level 1) for at least 1 chemical on the list.

Type of gloves Breakthrough time
A ≥ 30 min for at least 6 chemicals
B ≥ 30 min for at least 3 chemicals
C ≥ 10 min for at least 1 chemical

The ‘chemical resistant’ glove pictogram must be accompanied by code letters for the tested chemicals for Type A and Type B gloves. Type C marked gloves are without any code letter.

List of chemicals:

Letter code Chemical CAS numbere Class
A Methanol 67-56-1 Primary alcohol
B Acetone 6764-1 Ketone
C Acetonitrile 75-05-8 Nitrile compound
D Dichloromethane 75-09-2 Chlorinated hydrocarbon
E Carbon disulphide 75-15-0 Organic compound containing sulphur
F Toluene 108-88-3 Aromatic hydrocarbon
G Diethylamine 109-89-7 Amine
H Tetrahydrofurane 109-99-9 Heterocyclic ether
I Ethyl acetate 141-78-6 Ester
J n-Heptane 142-85-2 Saturated hydrocarbon
K Caustic soda 40% 1310-73-2 Inorganic base
L Sulphuric acid 96% 7664-93-9 Inorganic mineral acid
M* Nitric acid 65% 7697-37-2 Inorganic mineral acid, oxidizing
N* Acetic acid 99% 64-19-7 Organic acid
O* Ammonium hydroxide 25% 1336-21-6 Organic base
P* Hydrogen peroxide 30% 7722-84-1 Peroxide
S* Hydrofluoric acid 40% 7664-39-3 Inorganic mineral acid, contact poison
T* Formaldehyde 37% 50-00-0 Aldehyde

*New chemicals

EN16523-1
Resistance to chemical degradation

Degradation is the deleterious change in one or more properties of a protective glove material due to contact with a chemical. Indications of degradation can be delaminating, discoloration, hardening, softening, dimensional change, loss of tensile strength, etc. It is determined by measuring the percentage change in puncture resistance of the glove material after a continuous contact for 1 hour of the external surface with the challenge test chemical. The results of the degradation test must appear in the information leaflet for all three glove types.

Protection against micro-organisms

Micro-organisms are defined by the standard as bacteria, fungi or viruses. To claim resistance to bacteria and fungi the glove must pass the penetration resistance test according to standard EN 374-2: 2014. If the glove passes ISO 16604: 2004 (method B) test it can claim resistance to viruses as well, and the term “VIRUS” will be added below the biohazard pictogram.

EN 374-5: 2016
Mechanical Risks

Revision of EN 388: 2003
The EN 388 standard underwent revision in 2016. SHOWA gloves are in the process of being recertified by the notified bodies to conform to the revised standard. Currently reported ISO 13997 cut resistance values are indications until officially certified. In the meantime the existing certificates according to EN 388: 2003 remain valid.

a) ABRASION RESISTANCE (0-4)
Number of cycles required to abrade a hole using abrasive paper in a circular sample of glove material under constant pressure and motion.

b) BLADE CUT RESISTANCE BY COUP TEST (0-5)
Number of cycles required to cut a sample using a stainless steel circular blade under constant speed and low force of 5 newtons (approx. 510g). For materials that dull the blade, after a certain number of cycles without cut through, the ISO 13997 test is performed and becomes the reference cut resistance value.

c) TEAR RESISTANCE (0-4)
Force required to propagate a tear in a rectangular sample of a glove with a starting incision, to a maximum force of 75N (approx. 7,6kg).

d) PUNCTURE RESISTANCE (0-4)
Force required to puncture the sample with a standard size steel point at a constant speed of 10 cm/min.

e) BLADE CUT RESISTANCE BY ISO TEST (A-F)
Force in newtons (N) required to cut through a sample using a rectangular blade in a specified cut test machine such as Tomodynamometer (TDM). This test is optional unless the blade in Coup test becomes dull, whereupon it becomes the reference for cut resistance. A letter value is assigned as follows:

Level of protection A B C D E F
Force in newtons > 2 5 10 15 22 30
Force in newtons Low Medium Medium High High High

f) IMPACT RESISTANCE (P) For protective gloves claiming impact resistance. Measures dissipation of force by the area of protection upon an impact of a domed anvil at an impact energy of 5 joules. Testing is carried out in accordance with the impact protection test for motorcycle protective gloves of EN 13594:2015 standard. A letter “P” is added on successful pass, while a fail remains unmarked.

Level X can also be applied for a – f above, which means “not tested”.

Level of protection 1 2 3 4 5
Abrasion resistance (number of cycles) > 100 500 2000 8000 -
Blade cut resistance by Coup test (index) > 1,2 > 2,5 5 10 20
Tear resistance (force in newtons) > 10 25 50 75 -
Puncture resistance (force in newtons) > 20 60 100 150 -
EN388: 2016
Cold-related risks

This standard applies to any gloves to protect the hands against convective and contact cold down to -50ºC.

Tested levels of glove performance in terms of the following risks:

  • Climatic or industrial cold transmitted by convection (0 to 4).
  • Climatic or industrial cold transmitted by contact (0 to 4).
  • Impermeability to water (0 or 1).

If the glove shows this symbol, it has achieved a performance index for (from left to right) climatic cold or industrial cold transmitted by convection, climatic cold or industrial cold transmitted by contact, impermeability to water.

“0” means that during the test level 1 was not reached.
“X” means that the test was not performed or not possible.

EN 511
Heat-related risks

Tested levels of glove performance in terms of the following risks:

  • Resistance to flammability (0 to 4)
  • Resistance to contact heat (0 to 4)
  • Resistance to convective heat (0 to 3)
  • Resistance to radiant heat (0 to 4)
  • Resistance to small splashes of molten metal (0 or 1)
  • Resistance to large splashes of molten metal (0 or 1)

“0” means that during the test level 1 was not reached.
“X” means that the test was not performed or not possible.

EN 407
Antistatic properties

Tested level of glove surface resistivity. Measured in ohms/square (Ω), this indicates the capacity of the glove to disperse via a dissipative and/or conductive effect the accumulated static electricity discharges on the operator’s hand.

It is applied to materials and articles that, at finished state, are intended to come into contact or are brought into contact with foodstuffs or with water that is for human consumption. According to Regulation 1935/2004: «The materials and articles must be manufactured in accordance with good manufacturing practice so that, under normal or foreseeable conditions for their use, they do not transfer their constituents to food in quantities which could:

  • Present a danger to human health,
  • Results in an unacceptable change in the composition of the foodstuffs or a deterioration in the organoleptic characteristics thereof.

All SHOWA gloves with the «food contact» logo are conform to Regulation (EU) No 1935/2004 and the Regulation (EU) No 2023/2006.

EUROPEAN DIRECTIVE 93/42/EEC
Covering medical examination and surgical gloves

Freedom from holes

A random sample of gloves is tested for freedom of holes by undergoing a water leak penetration test. The gloves are filled with 1l of water and must remain completely leak proof over a defined period of time. A failed test results in a higher AQL value, which for medical gloves sold in Europe must be 1,5 or lower.

AQL (accepted quality level) is a quality sampling procedure ISO 2859-1 used by manufacturers for measuring the % likelihood of pinhole defects in a batch of single use gloves. An AQL of 1,5 brings a statistical probability that less than 1,5% of the gloves in the batch will have defects.

Physical properties

Size and tensile strength requirements for single use medical gloves. No less than 240mm in median length and 95mm (±10mm) median width to provide adequate protection along full length of the hand (exception for long cuff gloves).

Strength is measured by elongation until breaking point, indicated as Force At Break (FAB) in newtons (N). FAB is measured on standard sample and on a rapid aged sample that is kept at 70°C for 7 days to simulate glove deterioration during prolonged shelf life. FAB requirements differ per glove material and if the glove is for examination or surgical purpose. Indication of median minimum FAB values:

Force at break (N) during shelf life

Rubbers (e.g. natural latex, nitrile) Thermoplastics (e.g. PVC, vinyl, butyl)
Examination glove 6,0 3,6
Surgical glove 9,0 -

Biological evaluation

A number of important requirements are specified to maintain biological safety of the glove for the medical practitioner as well as the patient. “LATEX” pictogram on packaging for natural latex rubber gloves is mandatory. No terms suggesting relative safety of usage are permitted i.e. low allergenicity, hypoallergenicity or low protein content. Powder residue, which is seen as unwanted contaminant on medical gloves, must not exceed 2mg per glove with “powder-free” claim. Water extractable latex protein content in latex gloves must not exceed 50 microgram per gram of rubber to minimize latex exposure that can cause allergic reactions. The level of endotoxins generated by bacteria on sterile gloves that claim “low endotoxin level” may not exceed 20 EU per glove pair (EU=Endotoxin Units).

Shelf life determination

The standard ensures there is no performance degradation during storage period prior to use. Accelerated aging tests are performed on glove samples to determine shelf life, to enable manufacturers to prove that their product will withstand (usually) up to 3 years and in some cases up to 5 years without losing their strength and protection properties.

A proper glove fit is crucial in ensuring the dexterity of the working hand. If the glove is too small, it cuts off blood circulation and restricts movement. On the other hand, a glove that is too large may slip off easily and make handling imprecise.
Glove size further to EN420 Hand: Palm Circumference (mm) Hand: Length (mm) Glove: Minimum Length (mm)
6 152 160 220
7 178 171 230
8 203 182 240
9 229 192 250
10 254 204 260
11 279 215 270
For an accurate fit, download and follow our glove size chart:

Sign Up for Our Newsletter

Get the latest news, happenings, and promos.

Contact Us

For product queries and consultation, get in touch with us at:

Excia Resources Sdn Bhd
F-3-6, Pacific Place, Jalan PJU 1A/4A, Ara Damansara, 47301 Petaling Jaya, Selangor D.E., Malaysia